Three Display Modes Of TFT LCD

Sep 02, 2025

Leave a message

                                                                        Three display modes of TFT LCD

The display mode of TFT LCD is mainly determined by the arrangement of liquid crystal molecules, the direction of electric field action and the configuration of polarizers. Currently, mainstream display modes include TN (Twisted Nematic), IPS (In-Plane Switching) and VA (Vertical Alignment), which have significant differences in structure, optical characteristics and application scenarios. The following systematic analysis of three modes from the principle level:

TN (Twisted Nematic) mode

The TN mode is the earliest commercial liquid crystal display technology. Its core feature is that liquid crystal molecules form a 90° helical twisted structure between two layers of glass substrates, and the friction direction of the upper and lower substrate orientation layers is orthogonal. When no voltage is applied, the liquid crystal molecules are arranged in a spiral arrangement, and the polarized light is rotated 90° by using the optical rotation characteristics. The principle is shown in Figure 1.

The TN mode is driven by a longitudinal electric field (vertical substrate direction). After voltage is applied, the liquid crystal molecules are arranged vertically, destroying the optical rotation characteristics. The upper and lower polarizers are orthogonal, and light is transmitted when there is no voltage (normal white mode), and light is blocked when the voltage is fully turned on (normal black mode). The TN mode uses positive liquid crystal (Δε>0), low threshold voltage (1-2V), short response time (1-5ms), but its contrast is low and light leakage is prone to dark state. This display mode uses a TFT array to control the light transmission and opaqueness of each pixel, thereby achieving the purpose of image display.

The display mode in which the LCD panel is bright when it is not applied to the voltage, and the display mode is dark after it is applied to the voltage is called Normally White (NW) mode. The display mode in which the LCD panel is in a dark state without voltage is applied, and the voltage is in a bright state is called Normally Black (NB) mode. In practical applications, in addition to the bright and dark states, when an appropriate voltage is applied to the liquid crystal, the intermediate tone between the bright and dark states is displayed, which is commonly known as the gray scale.

IPS (In-Plane Switching) mode‌

Principle of IPS display mode LCD display. In-Panel Switch Mode is an in-plane conversion mode, using negative liquid crystals, in which liquid crystal molecules exist in a plane parallel to the glass substrate. The settings of the upper and lower polarizers are the same as in the TN mode. They can only pass if the polarization direction of light is deflected. The difference is that in the IPS display mode, the horizontal electric field is used to control the deflection of liquid crystal molecules.

The polarization axes of the upper and lower polarizers in the IPS mode are perpendicular to each other, so the liquid crystal panel is in a dark state when no voltage is applied. When the voltage applied to the electrode is greater than the threshold voltage, the liquid crystal molecules rotate in the direction of the electric field on a plane parallel to the substrate, and are at a certain angle to the polarization axis of the upper and lower polarizers. Due to the birefringence effect of liquid crystal, a phase difference occurs between the ordinary light and the unusual light passing through the liquid crystal layer, so the liquid crystal panel is in a bright state.

TFT-LCD in IPS display mode has the advantages of good contrast, wide viewing angle, and good display effect. As an IPS upgraded version, FFS (Fringe Field Switching) generates edge electric fields through microelectrode arrays, making the molecules less inclination angle, higher brightness and lower power consumption.

VA (Vertical Alignment) mode‌

The electrode in VA mode is on the upper and lower substrates, and the liquid crystal molecules are deflected under the action of a vertical electric field. The VA mode uses negative liquid crystal. When no voltage is applied, the liquid crystal pointing vector is arranged vertically. In this case, the incident linearly polarized light does not undergo birefringence when passing through the liquid crystal layer, and the polarization state remains unchanged. If the polarization axes of the upper and lower polarizers are parallel to each other, the incident light passes through the upper and lower polarizers, and the display screen is bright. If the polarization axes of the upper and lower polarizers are perpendicular to each other, the incident light is blocked at the exit polarizer, and the display screen is in a dark state.

When no voltage is applied, there is no birefringence in the VA mode, so the VA in the normally black mode blocks light at all wavelengths and is independent of the box thickness. This feature shows that the dark state characteristics of the normal black mode are very good and the contrast is also very high, so actual VA products generally choose the normal black mode. When the voltage applied between the upper and lower electrodes is greater than the threshold voltage, the liquid crystal molecules deflect from the vertical alignment state to the horizontal direction. The birefringence phenomenon of the liquid crystal layer causes a phase difference, and the incident light passes through the upper and lower polarizers, and the panel is bright.

TFT-LCD in VA display mode has the advantages of good black color rendering, contrast, wide viewing angle, etc.

Through continuous technological innovation, the three display modes will maintain competitiveness in their respective areas of advantage. In the future, TN will stick to the niche market, IPS will dominate high-end mobile devices, and VA will lead large-size displays.

Send Inquiry