Analysis of the reasons for the splash screen of LCD LCD screen
LCD (Liquid Crystal Display) LCD screen is mainly composed of LCD panels, backlight modules, and driving circuits. Its normal operation depends on the coordinated cooperation of conditions such as stable power supply, synchronous driving signal, and accurate electro-optical response.
In actual engineering applications, LCD LCD screens sometimes have "splash screen" problems, which are manifested as: screen flickering, light and dark jumps, image jitter, afterimage, freezing or frame skipping, etc. The splash screen may occur in multiple links such as power-on, program burning, refresh abnormality, backlight control or environmental interference.
This type of problem not only affects the user experience, but may also cause misjudgment, resulting in return, failure of reliability verification, or interfere with the overall EMC performance of the system. This article will sort out the common causes of LCD splash screens from multiple dimensions of hardware structure, driver timing, software configuration and environmental factors.
1. Analysis of hardware-level reasons
The display performance of LCDs is highly dependent on the collaborative work of various internal components. Once a certain part of the functions are abnormal, it may cause obvious "splash screen" performance. The following will analyze several key subsystems one by one.
1. Backlight system failure
The LCD screen itself does not emit light, and its image requires a backlight to provide brightness. Modern LCDs mostly use LED backlights, and common faults include:
LED driver circuit is unstable: if the voltage fluctuates and the PWM dimming frequency is abnormal (it is very easy to be noticed by human eyes when it is below 150Hz), it may cause periodic flashing;
The backlight strip is damaged: a certain segment of LED fails, the entire backlight is affected, resulting in the splash screen or local darkness;
High voltage inverter problem (early CCFL LCD): Poor drive can cause the light to light up and go out.
2. Aging or damage to the LCD panel
The LCD panel is the core of the image rendering, and the problems are often reflected in:
Degradation or leakage of liquid crystal layer: long-term use or external impact causes unstable liquid crystal layer;
TFT driver array abnormality: Some TFT pixels cannot be driven correctly, causing the area to flicker;
Polarizer peeling or aging: causes uneven brightness or unstable color, which is manifested as flashing.
3. Poor contact with the connection line
Commonly used in equipment under long-term use or vibration environments:
FPC cable loose: the soft cable between the LCD module and the main control board is desoldered or virtually soldered;
LVDS signal line interference: If the high-speed differential signal line is disturbed or blocked poorly, it will cause image instability;
The interface socket wears: After multiple plug-ins and unplugging, the metal terminal contact resistance increases and the signal is attenuated.
Typical phenomena are when the device is gently shaken, or the screen flashes, or after re-pluging and unplugging the cable, it is temporarily restored to normal.
4. The power supply and main control circuit are abnormal
The power supply voltage is unstable: the LCD panel requires multiple voltages (VGH/VGL/AVDD, etc.). If the LDO/boost circuit is damaged, it will directly affect the driving stability;
Timing control chip (TCON) fault: responsible for clock/data synchronization. Once the steps are lost, the screen will be jumping and streaks;
Main control SoC overheating: After the driver chip temperature exceeds 85℃, it may enter a protection state, reducing the working frequency or black screen for a short time.
During the test, it was found that the TCON temperature increased by 10℃ and the stability decreased by about 7%; if the heat dissipation structure was poor, long-term high-temperature operation would greatly increase the probability of flashing.
5. Power-up and down timing control abnormality
LCD driver IC is extremely sensitive to power-on sequence and power-down behavior:
The power supply rails such as AVDD/VGH/VGL are not started or closed according to specifications, resulting in failure of internal locking;
The voltage rises too slowly and the IC cannot recognize the normal power supply;
The MCU still outputs a signal after power-down, causing data back-write or gate misdrive.
6. Synchronous signal abnormality (VSYNC/HSYNC/DE)
Synchronous signal errors will directly lead to confusion in image refresh logic:
MCU initialization failed, VSYNC was stuck (high level does not switch);
The DE signal is continuously effective and shows freezing;
The controller reset failed, the image data is misaligned or the grayscale exception.
2. Analysis of the reasons at the software level
In addition to hardware factors, LCD displays also rely on software-layer driver control, especially on embedded devices and PCs.
1. Graphics card driver is incompatible
The operating system does not match the driver: the matching graphics card driver is not installed after updating the system, which can easily cause the refresh rate setting error;
Driver cache conflict: When multiple screen outputs or frequent resolution switching, memory management errors cause the screen to jump;
Color depth/frequency setting is abnormal: If the error is set to 30Hz output, it is very easy to have a "splash screen" feeling.
For example, when connecting an external TV in a Windows system, if the display refresh rate is automatically set to 24Hz by the system, the LCD screen will flash frequently, affecting the visual experience.
2. Embedded system software configuration error
Such as smart terminals, on-board systems, etc.
Screen initialization timing error: For example, Vsync and DE signals are not controlled correctly;
I2C communication is unstable: screen parameter reading error affects Gamma curve and backlight control;
Dynamic dimming algorithm error: Automatic brightness adjustment logic error may cause frequent backlight PWM jumps.
The synchronous configuration and timing output of the test screen commonly used logic analyzers and oscilloscopes in development are key means to troubleshoot such problems.
3. Firmware or operating system bugs
Some Linux or Android kernel versions have unfixed bugs under specific driver frameworks, such as:
Some MTK chip versions of the Android platform have Race Condition when the backlight PWM synchronous control is controlled, resulting in intermittent flickering;
In the firmware of some domestic manufacturers, the dimming curve is not linearly planned, causing serious flashing at low brightness.
3. Usage environment and operation factors
Although the LCD screen is closed in a fixed structure when working, some environmental conditions may still induce or exacerbate the splash screen problem:
1. Electromagnetic interference (EMI): Strong electromagnetic fields such as industrial equipment, high-voltage wires, and radio transmission sources may interfere with signal transmission, causing image jump or deformation;
2. Electrostatic discharge (ESD): Static electricity accumulates in a dry environment, and is released instantly when it comes into contact with or close to the screen, causing the control circuit to fail for a short time;
3. Humidity and temperature fluctuations: Extreme temperature (<0℃ or >60℃) or humidity changes may affect the arrangement of liquid crystal molecules, and temporary splashing occurs;
4. Power supply fluctuations: Unstable mains, poor ground wire or poor power adapter quality may also cause intermittent picture distortion or flickering.
Although environmental factors account for a small proportion of LCD splash screen problems, they still need to be considered in high-end precision or harsh industrial occasions.
The "splash" problem of LCD screens covers hardware, drivers, signals, power supplies, and environment factors, and is a very challenging type of fault in product engineering debugging. Only by starting from the system perspective and checking layer by layer on power supply stability, timing integrity and driving accuracy can we accurately locate the root cause of the problem.
During the product design stage, timing tolerance, electromagnetic interference isolation and boundary behavior under high temperature and high humidity should be fully considered, so as to avoid bringing unstable factors into mass production and ensure the long-term and stable operation of the LCD system.
